Skip to content

Preparing the MCDU

This guide will help you prepare the MCDU in the A32NX for your departure. It includes a simple route that you can use to follow along easily and replicate in the simulator.

Disclaimer

This is for simulation purposes only.

The level of detail in this guide is meant to provide a FlyByWire A320neo beginner the ability to adequately program the MCDU to conduct and complete a flight.

A beginner is defined as someone familiar with flying a GA aircraft or different types of airliners. Aviation terminology and know-how is a requirement to fly any airliner, even in Microsoft Flight Simulator.

You will find many great videos on YouTube on how to fly the FlyByWire A32NX.
Check out the FlyByWire YouTube Channel as well: FlyByWire on YouTube

The simBrief route used in this guide:

AIRAC Updates

Please note, we may update this OFP and guide from occasionally to ensure it is current with the latest AIRAC provided by the simulator or external navdata.

Download simBrief OFP

Prerequisites

Below are a few Prerequisites before programming the MCDU.

Visit Starting the Aircraft to learn more.

  • Make sure the aircraft is powered up.
    • External Power OR APU
  • Make sure the ADIRS are set to NAV.
  • Have a valid flight plan.
  • Ensure IFR clearance has been obtained.

Requesting IFR Clearance

Before departing for the flight, we must obtain an IFR clearance from ATC. The clearance may be obtained from clearance delivery or another specific frequency, depending on the airport and available services.

If you are not flying on a network and are using the built-in ATC menu, simply find the appropriate selection in the menu and request for IFR clearance.

Clearances will usually provide the following information below. As a pilot, you would need to read back the clearance correctly or acknowledge it if using the built-in ATC menu.

  • Cleared to the destination via specified route in the filed flight plan.
  • Initial cleared altitude after departure.
  • Assigned SID for departure OR radar vectors
  • Assigned departing runway.
  • Transponder/squawk code.
  • Departure frequency.

Additional reading material: The CRAFT mnemonic

Chapters / Phases

This guide will cover the following topics:

  1. Understanding the MCDU
  2. MCDU Programming
  3. Entering Squawk Code
  4. A32NX simBrief Integration

Understanding the MCDU

During this guide we will be referring to a few key terms which are defined below.

Line Select Key (LSK)

LSK for short. These keys are on the left and right-hand side of the MCDU screen. They are highlighted in the image below.

  • Left-hand keys are referenced (in descending order) as LSK1L - LSK6L.
  • Right-hand keys are referenced (in descending order) as LSK1R - LSK6R.

mcdu1

Slew Keys

These keys are referenced below.

mcdu1a

Info

These keys scroll between certain pages, i.e., INIT A and INIT FUEL PRED when the INIT page is selected.

These keys scroll vertically on certain pages, i.e., F-PLN page.

MCDU Programming

D.I.F.S.R.I.P.

Pilots commonly use the acronym above when programming the MCDU. It represents the following flow on the MCDU:

The simBrief route used in this guide - Available Here

DATA

This MCDU page provides various data for the pilots. It has two pages (accessed by using the horizontal slew keys). It will not be used for this tutorial.

DATA includes the pages below:

  • Position Monitor
  • IRS Monitor
  • GPS Monitor
  • A/C Status
  • Closest Airports
  • Equitime Point
  • Waypoints
  • NavAids
  • Runways
  • Routes

INIT A

Automatic OFP Imports via INIT REQUEST

Please note that the INIT REQUEST option will not appear if you have selected both a departure and arrival on the MSFS world menu before loading into your flight.

For more information and a guide to our simBrief A32NX features, visit the page below:

FMS (MCDU) and simBrief Integration

FROM/TO Field

  • Using the keypad, type in EDDM/EDDF
  • Once this is in the scratch pad, press LSK1R.
  • This following screen would show "company routes". Since there are none stored, select Return using LSK6L.

mcdu5

FLT NBR

  • Using the keypad, type in EZY123 and press LSK3L. Feel free to use your own flight number here!
  • If you have the Free Text module enabled for your flight, this will enable other users flying the A32NX to send you messages. This will not be covered in this guide.

COST INDEX

ofp1

The cost index can be found in the image above.

  • Using the keypad, type in 10
  • Press LSK5L.

Wind Requests

Pilots can choose to import your wind data at this stage through the WIND/TEMP option by pressing LSK 4R. For more information on using this feature, please see the guide below.

Wind Request Guide

Please also note the following:

  • Per-waypoint entry and request of cruise winds is still being implemented.
  • Wind Request functionality is not 100% accurate to the real aircraft.
    • In real life, selecting the wind requests option on the climb page would populate the wind data for all stages of flight.

CRZ FL/TEMP

ofp2

Input the desired cruise flight level in this field. On our OFP, this is listed as 0240 or FL240.

  • Using the keypad, type in 240
  • Press LSK6L

This will input FL240 and the temperature as well.

FLIGHT PLAN

Upon loading the flight plan page, there will be three entries. Departure airport, a discontinuity and arrival airport.

Our route for this flight can be found on the 2nd page of the OFP

Routing Disclaimer

Note that waypoints, STARs, and SIDs may be called differently due to different nav-databases or different AIRAC cycles between simBrief and the simulator.

ofp3

EDDM/08L GIVMI6Q GIVMI Y101 ERNAS T161 DEBHI DEBHI1C EDDF/07L

Inputting a SID

SID

Standard Instrument Departure Route

These are procedures that are defined and published that take a flight from the take-off phase to the en route phase.

Also see: SIDS and STARS

To program the Standard Instrument Departure (SID):

  • Press LSK1L or EDDM (the departure airport)
  • Select DEPARTURE shown next to LSK1L
  • Select the runway we are departing from. In this case 08L using LSK2L
  • On the list of SIDs select the GIVMI6Q departure

The MCDU should now show at the top of the screen in yellow what is selected for our departure from EDDM.

mcdu8

  • Press INSERT* using LSK6R to program this into the flight plan.

Our flight plan should now have the associated waypoints for the GIVMI6Q SID. We can scroll through the flight plan using the vertical slew keys. The SID terminates at GIVMI and this is where we can begin to fill out the rest of the flight plan.

GIVMI6Q ILS Frequency

When selecting a departure SID that pairs with a LOC/ILS frequency, the respective frequency will be autopopulated in RADNAV provided it is available from the navdata.

Enroute Flight Plan

  • Press the LSK that matches the location of GIVMI on the MCDU screen.
  • Select AIRWAYS using LSK5R.
  • Using the keypad, type in Y101 (the airway) and press LSK1L.
  • Using the keypad, type in ERNAS (waypoint) and press LSK1R.
    • Remember: Airways are on the left and waypoints are on the right.
  • Continue inputting the airway T161 and following waypoint DEBHI.

mcdu10

  • Press INSERT* using LSK6R to program this into the flight plan.

DCT Before a Waypoint

There will be cases where your flight plan has waypoints and no airways, or a mix of both. When you go direct from one waypoint to another, it will usually look like the following: WAYPOINT DCT WAYPOINT. You might also see directs represented as two waypoints without a separator, which looks like WAYPOINT WAYPOINT.

Let's look at an example and understand how to program these into the MCDU. (Please note this is not applicable to the sample flight plan in this guide, and we plan to create a more advanced flight plan entry guide at a later time.)

Below is the current flight plan we are utilizing:

Current Sample Flight Plan
EDDM/08L GIVMI6Q GIVMI Y101 ERNAS T161 DEBHI EDDF/07L

Let's imagine for this example that there was no airway between GIVMI and ERNAS, as well as between ERNAS and DEBHI. The flight plan would look like the following:

Example NO AIRWAY Flight Plan
EDDM/08L GIVMI6Q GIVMI DCT ERNAS DCT DEBHI EDDF/07L

The airways Y101 and T161 were replaced with DCT indicating from waypoint GIVMI proceed direct to ERNAS and after that proceed direct to DEBHI.

When you encounter this type of routing, there are a couple of ways to input this leg without the use of the airways page on the MCDU.

One of the easiest ways is utilizing the lateral revision page. To do this, simply find the starting waypoint on your F-PLN page, which in this case is GIVMI.

  • Use the relevant LSK to select it.

  • You will then be on the following page:

    lat-rev-fpln.png

  • Type in ERNAS so it's visible in the scratchpad.

  • Use LSK3R to enter ERNAS as the next waypoint on your flight plan.

Planning the Arrival

For the purposes of this guide, we will pre-plan our arrival into EDDF via the DEBHI1C STAR into 07L.

STAR

Standard Terminal Arrival Route

Similar to the SID, these are procedures that are defined and published that take a flight from the last point in a route (in our case DEBHI) to the first point in the approach or the initial approach fix (IAF).

Also see: SIDS and STARS

Find EDDF in green in the flight plan OR select EDDF in white under DEST using the corresponding LSK.

  • Select ARRIVAL using LSK1R
    • We will be shown the approaches available, designated by Type Rwy.
    • For this guide, we will shoot for an ILS to keep it simple.
  • Use the vertical slew keys to find ILS07LY and select it using the corresponding LSK.
  • A designator such as Y or Z may be present. This suffix is to distinguish in the navigation database a difference between approaches to the same runway. While similar in nature, they may have different minimums, allowed equipment, or other differences.
  • Again, use the vertical slew keys to find the STAR for this flight DEBHI1C and select it using the corresponding LSK.
  • For the approach VIA, select DF454, using the appropriate LSK. On the following page, we can choose transitions, if available, but for this flight, we don't.
  • Press INSERT* using LSK6R to program this into the flight plan.

mcdu12

Verify the flight plan by using the vertical slew keys to scroll through it.

Discontinuity

Discontinuity

The flight plan might contain so-called discontinuities. These are breaks in the flight plan and often separate two flight plan sections, like the SID and first in-route waypoint or the STAR and the APPR. They are also often inserted when the flight plan is modified.

Sometimes discontinuities are also part of a procedure to indicate that manual input is required (mostly clearance by ATC). The preceding legs are called MANUAL legs.

Discontinuities after a MANUAL leg can not and should not be deleted. See the Discontinuities link below.

In this flight plan we have a discontinuity between the STAR and approach procedure as shown below.

mcdu-discontinuity.png

See our detailed documentation for Discontinuities to understand how to appropriately handle these when

encountered on your F-PLN page. 

!!! warning ""
    Additionally, make note of this [Special Case](../a32nx-advanced-guides/flight-planning/disco.md#special-case) on the discontinuity page.

Viewing Flight Plan on ND

We can also verify the route looks correct by selecting Plan on the EFIS control panel and watching the ND as we scroll through.

SECONDARY FLIGHT PLAN

This page allows us to input a secondary flight plan. This page is currently inoperable in the A32NX. We will update this portion of the guide when it is usable.

RAD NAV

On this page, we would set any frequencies or identifiers needed for the departure and subsequently later en route those required for the arrival.

For the purposes of this guide, we will be using frequencies on the RADNAV page.

If we would like to have additional navaids for the departure, we can input the runway localizer for runway centerline guidance on the PFD and the initial procedure turn, including the BRECON VOR (BCN) to verify the track en route to BCN. This is a little more advanced than this guide allows for, but we will cover how to input frequencies.

VOR

The A32NX supports VOR autotuning when in range of a VOR before departure. You can verify this by checking the RADNAV page and seeing if the VOR frequency is already populated. You should verify the relevance of this VOR to your departure procedure and flight plan before takeoff.

On this departure SID, we have routing instructions that rely on the Munich VOR DMN with a frequency of 116.0.

Departure ILS

When selecting the SID earlier in the flight plan section, the A32NX should have autopopulated the ILS/LOC frequency. If it hasn't, we can manually insert it for centerline guidance on take off.

Our departure runway is EDDM/08L (runway 08 left), which has a frequency of 109.50. When inputting a frequency, and we are in range of the ILS, it will autopopulate the identifier and course. You could also enter the identifier IMNE and it would automatically fill in the frequency. You cannot enter both at the same time, as this would result in a FORMAT ERROR.

  • Using the keypad, type in 109.50 and press LSK3L to input it.

Arrival ILS

With an ILS or LOC approach selected, the arrival ILS frequency should be automatically tuned correctly whenever the aircraft is in climb phase or greater and within 250 NM of the destination. Ensure that we verify the ILS frequency when we reach the arrival phase of the flight - see Approach and Landing (ILS).

Remember, our arrival airport/rwy is EDDF/07L with ILS07L having a frequency of 110.30. When inputting a frequency, and we are in range of the ILS, it will autopopulate the identifier and course. There is no need to fill these fields. You could also enter the identifier IFEL and it would automatically fill in the frequency. You cannot enter both at the same time, as this would result in a FORMAT ERROR.

  • Using the keypad, type in 110.30 and press LSK3L to input it.

mcdu15

ADF

This works much in the same way as the examples above.

INIT FUEL PRED

To navigate to the INIT FUEL PRED page, we first have to select the INIT button. Once on INIT A, use the horizontal slew keys to switch the page to INIT FUEL PRED.

On this page, we can input our zero fuel weight (ZFW) and zero fuel weight center of gravity (ZFWCG).

Important Info - FMS Gross Weight (FMS GW)

Fuel and payload have to be set in the aircraft (see link below) and passenger boarding has to be complete or in progress for the ZFW/ZFWCG values to be correct. The "planned" payload values are used for the calculation if boarding has not been completed.

Gross Weight (GW) value on the ECAM will appear only when certain conditions are satisfied:

  • This page (INIT FUEL PRED) has a ZFW/ZFWCG value. Reminder: After engines are started, INIT FUEL PRED changes to the FUEL PRED page.
  • At least one engine is running.

Please see our Fuel and Weights Guide for more detailed information.

The A32NX can autopopulate this information.

  • Press LSK1R to load in the calculated ZFW/ZFWCG into the scratch pad at the bottom of the MCDU (after boarding has been started in the flyPad).
  • Press LSK1R a second time to input the above calculation into the MCDU. (The empty orange boxes should now be filled in by the scratch pad entry).

Now we can add our fuel on board (FOB). The amount we input in this field can be done in one of three ways:

  • Indicated FOB on the upper ECAM.
  • We can have the MCDU plan the amount of fuel required.
  • The amount indicated in the OFP.

Loading Fuel

Via the EFB - Learn How

ECAM FOB

Look at the upper ECAM and note the FOB indicated. Let's say that amount is 4631 kg. When inputting the block fuel into the MCDU, it is referenced in "tonnes", which is 1000kg, and we should round to the closest decimal point.

  • Using the keypad, type in 4.7 and press LSK2R.

MCDU Planning

A Note on Fuel Planning

The fuel planning feature on the MCDU should only be used as a reference point before fueling the aircraft using the EFB.

Generating / using the value provided by this feature may not be accurate and does not actually load fuel into the aircraft.

We can choose to have the MCDU provide a recommended amount of fuel for the planned flight.

  • Press LSK3R to compute an amount of fuel.

The Block field will be populated with a calculated fuel amount.

  • Press LSK3R again to confirm the fuel.
  • We should load this amount of fuel via the EFB.

SimBrief OFP

We can use the planned block fuel stated on the OFP, which in this case is 4631 kg. When inputting the block fuel into the MCDU, it is referenced in "tonnes", which is 1000kg, and we should round to the closest decimal point.

  • Using the keypad, type in 4.7 and press LSK2R.
  • We should load this amount of fuel via the EFB option.

mcdu16

PERF

The performance page changes based on the relative stages of flight until we land the aircraft. When programming the MCDU on the ground, we start on the take-off performance page.

The flyPad onboard the aircraft is capable of calculating your required takeoff performance for your flight. Visit our flyPad Performance Page guide for more information.

flyPad Performance Page

For this flight, we will be taking off with a 1+F flaps configuration.

  • Using the keypad, type in 1 and press LSK3R

THS Field MCDU

Entry of the THS field is subject to airline SOP and may not be required.

The Trimmable Horizontal Stabilizer (THS) field is where we enter the stabilizer trim for takeoff based on the aircraft's takeoff CG (TOCG). Entering this value in the MCDU will trigger the F/CTL PITCH TRIM/MCDU/CG DISAGREE ECAM caution, if appropriate.

If you have already entered your flaps configuration in the step above, applicable entries are formatted /X.XDN or /X.XUP representing a trim value and nose down or up respectively.

Examples:

  • Nose down trim of 0.4 can be inputted as /0.4DN
  • Nose up trim of 1.5 can be inputted as /1.5UP

For the purposes of simulation, there are a couple of methods to set the value of THS, described below. We intend to add a better visual representation of the TOCG at a later time, since loadsheets are not available.

See the After Engine Start section to find the appropriate trim value and to physically set your trim.

GW CG

Insert a THS value based on the GW CG values found in the EFB Ground Services > Payload page or the Fuel Prediction page in the MCDU. While this will be slightly off versus TOCG because of taxi fuel consumption, this will be close enough to accurate values until a better TOCG display is implemented.

GW CG Values can be found:

CG to THS calculation:

  • CG to THS can be found in the downloable FBW checklist in our Standard Operating Procedures resources page.
  • The CG/THS markings on the trim wheel can be used to validate this.

Make sure to update this value or set the correct trim once your engines have started.

After Engine Start

Once the engines have been started, we can use the auto-calculated CG value (not the ZFWCG value) on the FUEL PRED page for determining the pitch trim setting. You can now update the THS setting (if you chose to input a THS value) in the take-off performance page and set the pitch trim using the trim wheel. Although the TOCG may be slightly different due to fuel being used for taxi, it will not change enough to require a change in pitch trim.

We can also choose to set a FLEX TO TEMP for the flight. The example we are using today is 60 degrees. This will normally be calculated via a pilot's company EFB or other tools, but for the sake of this guide, we will use the value of 60.

Read the following tip for more information on FLEX temp.

  • Using the keypad, type in 60 and press LSK4R

Flex Temp

Pilots can use the flyPad Performance Page to calculate Flex Temp for takeoff. The flyPad will also calculate if TOGA is the preferred thrust setting for takeoff and notify the pilot through the EFB.

flyPad Performance Page

What is Flex Temp?

Flex temp is entered into the MCDU, enabling the computer to use the pilot-specified air temperature to allow for take-off thrust that is less than TOGA but not less than CLB. This is a method of creating cost savings by increasing engine life, resulting in reduced overhaul and fuel costs. This value is normally calculated via a pilot's company EFB or other tools.

Flex temps are above ISA+29°C (44°C at sea level) and above current temp, but no higher than ISA+59°C (74°C at sea level). Usable Flex temps at sea level are from 45 °C (or current OAT if it is higher) to 74 °C.

Additionally, a decent rule of thumb for simulation purposes is to use a lower number if heavy or on a short runway and higher for the opposite.

Flex Temp Calculations Not Available in Stable

We have implemented our own takeoff performance calculator in the Development version.

Unfortunately, it is not yet available on the stable version.

Our SID chart mentions that the TRANS ALT for this departure is 5000 ft.

  • Using the keypad, type in 5000 and press LSK4L

V-Speeds

Pilots can use the flyPad Performance Page to calculate V-Speeds for takeoff.

flyPad Performance Page

Stable Version Only

V-Speeds are normally calculated by a company EFB or other tools. This feature is not yet available in the stable version. Instead, you can simply click the LSK next to the V-Speed you want to calculate, to get V-Speeds from a simplified calculation.

  • Press LSK1L to have the calculated V1 speed appear in the scratchpad.

mcdu19

  • Press LSK1L again to have the value inputted into the V1 speed. The value you get can be different from the one in the image as it depends on the weight of the aircraft.
  • Repeat this procedure for VR and V2.

The performance page should now look similar to this:

mcdu20

Entering Squawk Code

During your MCDU preparation or before departing from the stand, you should have obtained your IFR clearance. As part of this action, you will be given a transponder/squawk code for your flight. This allows ATC to identify your aircraft on their radar.

To enter your assigned code find the ATC/TCAS Panel on the bottom right portion of the lower pedestal. It will look like this:

ATC-TCAS.png

  • Ensure that the XPDR switch is on STDBY for now (will be set to AUTO or ON shortly before take-off)
  • To clear the current code, double press the CLR button.
  • Enter your assigned code using the keypad.

A32NX simBrief Integration

This section has been moved to our dedicated simBrief Integration feature guide.

After setting up the MCDU, continue with Engine Start and Taxi